IBM Security Verify

Hi,

I am working on a custom adapter and previously the adapter was working without problem, all the attributes was being showed, and all the AL run without problem, after a couple of dais I have to add a new attribute to the schema and to the account form and after that the driver attribute list does not show any objectclass or attribute on the connector, is any way to identify what is causing this issue?

I already do the following checks:

• service.def - file seems to be fine.
• schema.dsml - include all the previous attributes and the new one and the objectclass include the new attribute.
• ObjectclassAccount.xml - seems to be fine the file is correctly formatted.
• targetProfile.json - I generate the file with the "targetProfile.cmd" and check that all the groups and attributes are properly documented on the file.

There could be many reasons why this does not work - but as this a basically standard IGI (I assume based on the inclusion of targetProfile.json) you could raise a case to IBM Support if you are sure your adapter files are correct.

Have you tried to import the Adapter Profile (after packaging the new version in a jar file) on a IGI system that does not have it already ?
If not - this would probably be a good idea to start with - this would validate your adapter profile is correct and that it is the replacement that fails...

HTH

------------------------------
Franz Wolfhagen
IAM Technical Architect for Europe - Certified Consulting IT Specialist
IBM Security Expert Labs
------------------------------

Original Message:
Sent: Wed December 01, 2021 10:23 AM
From: Gabriel Labarrera
Subject: Driver Attributes List not being showd for custom adapter profile on SVG

Hi,

I am working on a custom adapter and previously the adapter was working without problem, all the attributes was being showed, and all the AL run without problem, after a couple of dais I have to add a new attribute to the schema and to the account form and after that the driver attribute list does not show any objectclass or attribute on the connector, is any way to identify what is causing this issue?

I already do the following checks:

• service.def - file seems to be fine.
• schema.dsml - include all the previous attributes and the new one and the objectclass include the new attribute.
• ObjectclassAccount.xml - seems to be fine the file is correctly formatted.
• targetProfile.json - I generate the file with the "targetProfile.cmd" and check that all the groups and attributes are properly documented on the file.

Hi Franz,

I did delete the connector that already existed on the system, and this could be a error on my side, but the solution for me was to try a "test connection" and after that all the attributed were listed on the connector tab.

I dont know if this is how is intended or if this only happens on custom profiles, as far as I recall this did not happened with the Verify Access connector.

Thank you for the help.

------------------------------
Gabriel Labarrera
------------------------------

Original Message:
Sent: Thu December 02, 2021 04:59 AM
From: Franz Wolfhagen
Subject: Driver Attributes List not being showd for custom adapter profile on SVG

There could be many reasons why this does not work - but as this a basically standard IGI (I assume based on the inclusion of targetProfile.json) you could raise a case to IBM Support if you are sure your adapter files are correct.

Have you tried to import the Adapter Profile (after packaging the new version in a jar file) on a IGI system that does not have it already ?
If not - this would probably be a good idea to start with - this would validate your adapter profile is correct and that it is the replacement that fails...

HTH

------------------------------
Franz Wolfhagen
IAM Technical Architect for Europe - Certified Consulting IT Specialist
IBM Security Expert Labs

Original Message:
Sent: Wed December 01, 2021 10:23 AM
From: Gabriel Labarrera
Subject: Driver Attributes List not being showd for custom adapter profile on SVG

Hi,

I am working on a custom adapter and previously the adapter was working without problem, all the attributes was being showed, and all the AL run without problem, after a couple of dais I have to add a new attribute to the schema and to the account form and after that the driver attribute list does not show any objectclass or attribute on the connector, is any way to identify what is causing this issue?

I already do the following checks:

• service.def - file seems to be fine.
• schema.dsml - include all the previous attributes and the new one and the objectclass include the new attribute.
• ObjectclassAccount.xml - seems to be fine the file is correctly formatted.
• targetProfile.json - I generate the file with the "targetProfile.cmd" and check that all the groups and attributes are properly documented on the file.