Power

 View Only

  • 1.  eBMC power 10

    Posted Wed July 17, 2024 02:17 PM
    Edited by Marvin Jones Wed July 17, 2024 02:17 PM

    Hello,

       has anyone have or resolved this issues where the "power 10" connection to the HMC via  this new ebmc state is showing "Fail authentication " i put in the correct password and it still say fail authentication.  the P8 or P9 i can just login to ASMI and update the "HMC Access password " with this new eBMC  this is not the case not that i know of .  Can anyone out there help me with this ? i seen those videos but those just tell me how to set it up . 



    ------------------------------
    Marvin Jones
    ------------------------------



  • 2.  RE: eBMC power 10

    Posted Thu July 18, 2024 01:42 AM

    Hi,

    in my case, this error occurred with version differences between HMC and eBMC (Systems comes with FW1030 and HMC was on v10r2m1021).
    Try to access the eBMC directly on the system and check the access password locally, also System Firmware Levels.

    Best regards
    Manfred



    ------------------------------
    Manfred Hettmann
    ------------------------------

    Original Message


  • 3.  RE: eBMC power 10

    Posted Thu July 18, 2024 02:45 PM

    hello Manfred ,

       looks like the fw  is on latest MM1050, so looks good there. 



    ------------------------------
    Marvin Jones
    ------------------------------

    Original Message


  • 4.  RE: eBMC power 10

    Posted Thu July 18, 2024 06:22 AM
    Edited by Rohit Chauhan Thu July 18, 2024 06:34 AM

    Hello,

    I faced similar issue with P10 S1024 servers so i decided to upgrade the server firmware and it did solved it. Not sure if it is the same issue but it is worth to give a restart as well. I hope this is new server so it can be done quite easily ?



    ------------------------------
    Rohit Chauhan
    Senior Technical Specialist
    Norway
    ------------------------------

    Original Message


  • 5.  RE: eBMC power 10

    Posted Thu July 18, 2024 02:28 PM

    Hi  Rohit,

        thanks for the response.  so the firmware level is MM1050_52 what i do notice is the system  has no connection  but the VMI connection action button is grey out. not sure what's that about. 



    ------------------------------
    Marvin Jones
    ------------------------------

    Original Message


  • 6.  RE: eBMC power 10

    Posted Thu July 18, 2024 04:27 PM

    Hi Marvin,

    Is the cabling good between the server and hmc ? Please also try restarting the server and then check the VMI configuration option . It should still be active even if there is no connection status.



    ------------------------------
    Rohit Chauhan
    Senior Technical Specialist
    Norway
    ------------------------------

    Original Message


  • 7.  RE: eBMC power 10

    Posted Thu July 18, 2024 09:58 AM

    This series of short videos is very good if you have not already viewed them.  POWER10 EBMC Video Series - IBM MediaCenter 



    ------------------------------
    Charlie Berry
    ------------------------------

    Original Message


  • 8.  RE: eBMC power 10

    Posted Thu July 18, 2024 02:44 PM

    HI Charlie,

       yes i seen the BMC video. Good stuff. However those do not resolved my issues. 



    ------------------------------
    Marvin Jones
    ------------------------------

    Original Message


  • 9.  RE: eBMC power 10

    Posted Mon August 05, 2024 03:32 PM

    Hello everyone,

        That's for the help here. We had to replace the eBMC to get this machine up and running. seem like there some hardware issues here. per IBM



    ------------------------------
    Marvin Jones
    ------------------------------

    Original Message