AIX

AIX

Connect with fellow AIX users and experts to gain knowledge, share insights, and solve problems.


#Power
#Power
 View Only
  • 1.  PORT LACP FAILURE

    Posted Thu October 23, 2025 03:49 AM

    Dears:

    Thank you for your assistance. I have a S922 server that has recently been frequently reported error related to LACP out of sync, than recovery immediately, and there is no link error.

    The network switch has no error, and LACP transfers health.

    I want to find the root cause, and needs your help. Thank you very much.



    ------------------------------
    Bowen Dai
    ------------------------------


  • 2.  RE: PORT LACP FAILURE

    Posted 30 days ago

    Hi Bowen, 

    Found this IBM Support doc related to the same error.
    https://www.ibm.com/support/pages/ibm-aix-troubleshooting-echportoutofsyn-errors-ieee-8023ad-link-aggregationlacp-etherchannel

    Can you try the steps and resolution mentioned in the above link...



    ------------------------------
    Saikrishna Akkela
    ------------------------------



  • 3.  RE: PORT LACP FAILURE

    Posted 30 days ago

    Root cause probability: 1. cable/connector, 2. SFP+ on any side (LAN card or switch), 3. firmware in LAN card (check from HMC). 



    ------------------------------
    Igor Novotny
    MHM Computer, a.s.
    Czech Republic
    ------------------------------



  • 4.  RE: PORT LACP FAILURE

    Posted 28 days ago

    Hi

    what is the status of primary aggregation status is Negotiating  ,as per below screen shot and the status should be Aggregated , please double check the configuration from switch side.

    • Negotiating: LACP is in progress, but the switch has not yet aggregated the adapters. If the Link Aggregation remains on this status for longer than one minute, verify that the switch is correctly configured. For instance, you should verify that LACP is enabled on the ports.
    • Aggregated: LACP has succeeded, and the switch has aggregated the adapters together.

    https://www.ibm.com/docs/en/aix/7.2.0?topic=configuration-ieee-8023ad-link-aggregation-troubleshooting

    also please check from HW side if there's any issue reported on PCI adapter ( Cable / SFP or FW)



    ------------------------------
    Anas AlSaleh
    IBM Power Systems Software Specialist
    Saudi Business Machines ( SBM )
    Riyadh
    ------------------------------



  • 5.  RE: PORT LACP FAILURE

    Posted 27 days ago

    I assume the following are true where the LACP errors are being generated:

    1. It's on a VIO server(s).
    2. The ports were all IN_SYNC for at least a month before going live.
    3. No known changes made from the VIOs or Network(switches) side.
    4. Using both Etherchannel and SEA

    Unfortunately, when it comes to network issues, often times you have to rule out your own environment first before engaging the network team. In this case, if you want to find out the root cause, start with process of elimination by removing each port out of your Etherchannel and test. 

    Good luck.



    ------------------------------
    Angel Bugarin
    ------------------------------



  • 6.  RE: PORT LACP FAILURE

    Posted 2 days ago

    > Unfortunately, when it comes to network issues, often times you have to rule out your own environment first before engaging the network team

    Having visibility to your adjacent environments is a must.

    Unless you know how to interpret a tcpdump, ask the network team to enable LLDP, and to check if LACP is long or short.  (Recommended setting is "long" on both sides, but as long as both side are configured for the same value, it should work).



    ------------------------------
    José Pina Coelho
    IT Specialist at Kyndryl
    ------------------------------