Greetings,

I am attempting to run the C2PJRECI job as documented in the zSecure Alert manual near the start of Chapter 4.

I n each attempt the job ends with a Return code 4 and the message,

No recipients defined for set aaaaaa     
(where aaaaaa is my Alert configuration).

There are multiple alerts set with email addresses, so I must have something else wrong. 
Any ideas?

Thanks
Lennie

Hi lennie,

So this job should send an email to every email address a list of which alerts they can receive. If you have alerts with destination email selected then a 4 (No recipients) is strange. The only thing i can think of is that you also selected " Redirect e-mails to C2RSMTP DD" too and in effect no recipients. 

cheers

rene

Greetings,

I am attempting to run the C2PJRECI job as documented in the zSecure Alert manual near the start of Chapter 4.

I n each attempt the job ends with a Return code 4 and the message,

No recipients defined for set aaaaaa     
(where aaaaaa is my Alert configuration).

There are multiple alerts set with email addresses, so I must have something else wrong. 
Any ideas?

Thanks
Lennie

Rene,

Thanks for replying.

I do not have that option set. I have tried this on more than one system, with the same result. I fear I may be doing something wrong, but I cannot see what it is.

I see that email addresses can be set at the configuration level, at the category level, and at the individual alert level. I have assumed that if set at the alert level they do not need anything specified at the other levels. Is this correct?

What other tests or diagnostics can I try?

Lennie

Lennie

Hi lennie,

So this job should send an email to every email address a list of which alerts they can receive. If you have alerts with destination email selected then a 4 (No recipients) is strange. The only thing i can think of is that you also selected " Redirect e-mails to C2RSMTP DD" too and in effect no recipients. 

cheers

rene

Greetings,

I am attempting to run the C2PJRECI job as documented in the zSecure Alert manual near the start of Chapter 4.

I n each attempt the job ends with a Return code 4 and the message,

No recipients defined for set aaaaaa     
(where aaaaaa is my Alert configuration).

There are multiple alerts set with email addresses, so I must have something else wrong. 
Any ideas?

Thanks
Lennie

Hi lennie,

Setting a different kind of destination on the category level overrules the one set for the entire set.

Setting one for an individual alert will overrule the one set for a group (if one is set) or else the destination for the entire set.

The only 2 things i can think off are

Is the C2PCUST you use in the C2PJRECI the same one used in the Alert UI ?

Check the actual REPORT member. Does it really contain something like this ?

/*  Including member C2PS1401 for destination type MAIL */        
newlist type=SMF,                                                 
 mt=`rene_van_til@nl.ibm.com`,                                    
 from=`&jobname &system <rene@tvt8018.com>`,                      
 outputformat=emaildefault,                                       
 name=MAIL1401 header=no nopage                                   

cheers

rene

Hi lennie,

Setting a different kind of destination on the category level overrules the one set for the entire set.

Setting one for an individual alert will overrule the one set for a group (if one is set) or else the destination for the entire set.

The only 2 things i can think off are

Is the C2PCUST you use in the C2PJRECI the same one used in the Alert UI

Check the actual REPORT member. Does it really contain something like this ?

/*  Including member C2PS1401 for destination type MAIL */        
newlist type=SMF,                                                 
 mt=`rene_van_til@nl.ibm.com`,                                    
 from=`&jobname &system <rene@tvt8018.com>`,                      
 outputformat=emaildefault,                                       
 name=MAIL1401 header=no nopage                                   

cheers

rene

Rene,

Thanks for replying.

I do not have that option set. I have tried this on more than one system, with the same result. I fear I may be doing something wrong, but I cannot see what it is.

I see that email addresses can be set at the configuration level, at the category level, and at the individual alert level. I have assumed that if set at the alert level they do not need anything specified at the other levels. Is this correct?

What other tests or diagnostics can I try?

Lennie

Lennie

Hi lennie,

So this job should send an email to every email address a list of which alerts they can receive. If you have alerts with destination email selected then a 4 (No recipients) is strange. The only thing i can think of is that you also selected " Redirect e-mails to C2RSMTP DD" too and in effect no recipients. 

cheers

rene

Greetings,

I am attempting to run the C2PJRECI job as documented in the zSecure Alert manual near the start of Chapter 4.

I n each attempt the job ends with a Return code 4 and the message,

No recipients defined for set aaaaaa     
(where aaaaaa is my Alert configuration).

There are multiple alerts set with email addresses, so I must have something else wrong. 
Any ideas?

Thanks
Lennie